brand new and high quality.
Features:
This products maximum power 1800W, adopted super PCB layout esign and super heat sink, heat issipation good, since with a cooling fan interface, can also o ischarge, generator voltage inverter, etc.
This induction heating circuit uses 12-48V low voltage for C power supply, maximum current 40A, the most highest power is 1800W.
It can work continuously under the condition of good heat issipation. ue to its moderate power, it can be used by IY players to give smaller players the parts can be treated by quenching, annealing and other heat .
You can also be melt with crucible Kim, Silver, Copper, aluminum and other metal, heating evenly, is fast and very convenient.
In this test, the maximum power is close to 1600W, and the maximum current is 35A. This product is available at under the condition of good heat issipation, the utility model can work continuously for hours.
Note:
1. The power of heating is very large, except that the plate and components are hot, and the heat of copper tube is very high. The buyer can prepare water cooling system separately, can buy a small water pump and 2 meters of inner iameter of 4mm rubber hose.
2. You must pay attention to when using power supply, because the high-power ing power supply usually have soft start function, namely the output voltage is slowly rising, and if the voltage rise to 10V before connected induction heating circuit will be caused by lacking voltage lead to circuit can'for t afford to vibrate, so that the two MOS tube conduction and burned components at the same for time, so be sure to the power supply voltage stability and then access the induction heating circuit.
3. When heating the metal objects o not to heat too large metal, otherwise it may be overloaded with power, please add a 35A fuse or ammeter and air will be better. (package oes not inclues)
4. Although this rive plate can withstand more than 40A current, but it is recommended that not exceed 48V 35A to prevent accidents and amage.
5. Package comes with heating iameter is 60 mm, esign voltage is 36V, if you use more than 40 voltage power supply shall be used for inner iameter 70 mm above iameter heating ring, water pump use 12V for c power supply, please use separate power supply voltage regulator module to avoid burn out fan and water pump.
6. The minimum input voltage of the module is 12V, it oesn'for t mean all the 12V power supply can be used, some novice buyers may use a smaller power supply. This module has specific voltage and current requirements, the voltage 12V current must be more than 10A power supply can be used, if the power is too low will lead to the power output is greatly reduced, when the voltage is lower than 12V, it will lead to two MOS at the same for time conduction, will burn MOS tube;
7. If you find that the MOS tube fever, then the first thing to consider whether the power output meets the requirements.
8. o not empty the board, otherwise it will issue a very high frequency of noise, and then MOS tube will burn out
9. Induction heating is recommended to use 36V 20A power supply, 12V power supply is too small heating almost no response, and 12V power supply easily lead to the power supply output voltage ecreases, 12V is very angerous
10. Induction heating power is great, so fever is normal, be sure to o a good job of cooling.
11. Induction heating, the power recommended more than 48V 50A ing power supply. More than 24V power supply, then more than 20A power supply, the greater the voltage, the greater the current, the greater the heating power, heating faster.
Specifications:
Metal and Plastic
Size: approx.185x90mm/7.28x3.54in
Color: As pictures shown
Quantity: 1 Set
Note:
No retail package.
Please allow 0-1cm error ue to manual measurement. pls make sure you o not mind before you bid.
Due to the ifference between ifferent monitors, the picture may not reflect the actual color of the item. Thank you!
Package Includes:
1 PCB Board
1 Copper Tube
(other accessories emo in the picture is not included.)
החזר על אי אספקה
