Features:
*Brand new and high quality
*Made of high quality material, strong and
*The for W1209 is a low-cost yet powerful thermostat controller with a clear acrylic plastic housing. The module intelligently controls power to most types of electrical equipment based on the temperature detected by the included high- for precision remote temperature sensor.
*A cooler, heater or fan is connected to the power supply via relay contacts K0 and for K1 and the temperature on/off set point is programmed into the for W1209 using the onboard settings, increase and decrease buttons and display. Then, based on the temperature measured by the temperature sensor (included with the module) and the setpoint programmed into the for W1209 controller, the relay contacts open and close, acting as a power switch for the cooler/heater.
*Although the module has an embedded microcontroller, no programming knowledge is required. 3 tactile switches allow configuration of various parameters including on and off trigger temperature.
*The onboard relay can switch a maximum current of 14V DC 20A, 24V DC 16A or 125V AC 7A. The current temperature is shown in degrees Celsius via a 3-digit seven-segment display and the current relay status is shown via an on-board LED.
Specification:
*Temperature control range: -50°C to +110°C (-58°F to +230°F)
*-9.9 to 99.9 resolution: 0. C
*Resolution at all other temperatures: C
*Measurement accuracy: 0.℃
*Control accuracy: 0.℃
*Refresh rate: 0.5 seconds
*Input power (DC): 6V to 12V @ 65mA maximum (provides power to the module, not the load)
*Measurement input: (10K 0.5%)
*Waterproof sensor: 0.5M cable
*Probe tip dimensions: 20mm long x 4mm diameter
*Output: relay output, capacity: 14V DC 20A, 24V DC 16A, 125V AC 7A
*energy consumption:
*Quiet current: < =35mA
*Operating current: < =65mA
*Environmental requirements:
*Temperature: -10～60℃
*Humidity: 20-85%
* for W1209 board (LxWxH): 48mm x 40mm x 14mm (.9" x .6" x 0.6")
*Case (length x width x height assembled): 59mm x 51mm x 18mm (2.3" x 2.0" x 0.71")
The display shows the measured temperature by default.
*Short press the "SET" button, then press the "+" and "-" buttons to increase or decrease the temperature setpoint.
*Long press the "SET" button to activate the menu to change the P0 to P6 parameters listed in the settings table below.
*Setpoints and all parameter settings are stored in non-volatile memory and are retained when controller power is turned off.
Notice:
The maximum input supported voltage should not exceed 12V. In applications such as automobiles or RVs where the battery voltage may exceed 12V, a voltage regulator circuit such as a 1N5349A Zener diode and a 20 Ohm series resistor in the 1W range should be used to limit the voltage to 12V. Alternatively, a 12V to 9V converter with its input connected to the battery and its output connected to the for W1209 will provide a stable 9V DC power supply to the for W1209.
Setup diagram:
*description/scope/default
*P0: Set heating or cooling mode / C/H / C
*P1: Hysteresis setting/0. - 15C/2C
*P2: upper temperature limit/110C/110C
*P3: Lower temperature limit / -50C / -50C
*P4: Temperature calibration / -7.0C ~ 7.0C / 0C
*P5: Delayed start time/0-10 minutes/0 minutes
*P6/P7: High temperature alarm/0C - 110C/off
*P8: Factory reset (not included in all firmware versions. Can also be reset by holding the + and - buttons for 5 seconds.)
Package includes:
1X digital temperature control switch sensor module
1X Acrylic clear box with mounting screws (assembly required)
Notes:
. Due to various factors such as display brightness and light brightness, the actual color of the product may be slightly different from the website picture.
2. Please allow a slight deviation between the data and the manual measurement.
