6KW Stainless Steel Internal Control Sauna Stove Heater for Steaming Room Bathroom Equipment

Feature: 1. High heating efficiency, long working hours, specially designed for small and medium?sized bathrooms and saunas. 2. Easy to install and can be placed in the sauna room, just adjust the support frame on the back of the sauna stove. 3. Using high?hardness stainless steel material, strong and durable, high temperature resistant. 4. With knob digital display controller, 30?120 celsius temperature controller and 1?8 hours time controller. 5. The necessary conditions are 15percent ?30percent relative humidity, 65?85 celsius temperature, and more rock load. 6. Thermostat can control the temperature in a great state. According to the size of sauna room, sauna heater can up to set temperature after 30?60 minutes. 7. It is widely used in apartments, hotels, indoor swimming pools, sauna rooms, steam rooms, fitness centers and other commercial facilities. Specification: Condition: 100percent Brand New Item Type: Sauna Heater Material: Stainless Steel Weight: Approx. 10850g / 382.7oz Product Size: Approx. 56.5x40.5x28.5cm / 22.2x15.9x11.2in Power: 6KW Use Space: 5-9 Furnace Tube Voltage: 220-380V Minimum Distance: Side: 10cm / 3.9in, Floor: 500mm / 19.7in or More, Shelf Distance: 15cm / 5.9in, Ceiling: 110cm / 43.3in, Floor: 18cm / 7.1in Application: Apartments, hotels, indoor swimming pools, sauna rooms, steam rooms, fitness centers and other commercial facilities. Installation Method: 1. Install the sauna stove to the wall with the provided screws. The stove can also be installed in the niches with a minimum height of 1900 mm. 2. The wall behind the furnace cannot be covered with asbestine cement, asbestine board or similar materials, because the covering will cause the wall material to exceed the allowable temperature limit.3. Use qualified materials for wall and ceilings. Power Cord Connection: 1. The connection of the power cord should be completed by a professional electrician, and in accordance with the current specifications, use REVE rubber insulated cables (or similar) to connect to the main power supply of the furnace. 2. The connection box of the stove is equipped with wiring terminals, and the crossed section of the connection wire is the same as that of the sauna heater. The junction box in the sauna room must be sealed, splatter-proof, and have a moisture condensation hole with a diameter of 7 mm. The center of the box must not be 500 mm above the ground. Sauna Stone: The sauna stone may be dusty, so we recommend to rinse it before putting it in the stone warehouse. The largest stone is placed at the bottom, and it should not be too tight when placed, and pay attention to leaving a ventilation space. The stone must be replaced when it starts to peel to avoid damage to the sauna heater. The diameter of the stone is generally 3-8 cm. Temperature Control: According to the size of the sauna room, the sauna heater can up to

the set temperature after 30-60 minutes. The sauna room maintains a uniform and comfortable temperature and adjusts itself as needed. Ventilation: In order to make the sauna as comfortable as possible, the sauna room must have good ventilation. It is best to drill an air hole in the wall panel near the bottom of the sauna heater to let air in from there. The diameter of the air inlet should be at least 6cm. The air outlet is best on the wall opposite to the air inlet, and the farther away from the air inlet, the better. The diameter of the air outlet should be twice that of the air inlet, and it should be as far away as possible from the ground and lower than the upper seats. . Package List: 1 x Sauna Heater Stove Note: 1.Please allow 0?1 inch error due to manual measurement. Thanks for your understanding.2.Monitors are not calibrated same, item color displayed in photos may be showing slightly different from the real object. Please take the real one as standard.3.The power switch is the main power switch of the sauna heater. The user must turn off the power switch when leaving the sauna.4.Note that the upper screw should be fastened well, leaving gaps of 3mm between the screw head and the wall.5.Do not cause unnecessary skin damage, and the temperature control needs to be adjusted according to the temperature that the individual bears.